|
Job/Description |
Who ? |
Pri |
Done |
| |
|
|
|
Building
|
|
|
|
|
Seal door on 5th floor |
Steve |
1 |
|
|
Run gasoline engine, open and close doors. |
Steve |
2 |
|
|
Remove and Repair Gas engine. |
Steve |
1 |
|
|
Paint fourth floor |
Steve |
3 |
|
|
Hydraulic service |
Steve |
1 |
|
|
Clean track. |
All |
1 |
|
|
Adjust building wheels |
Steve |
1 |
|
|
Crane maintenance |
Steve |
1 |
|
|
Fans in 5th floor walls |
Steve |
2 |
|
|
Building drive tests |
Harry |
2 |
|
|
Door and roof limit switches |
Steve |
1 |
|
|
Check lights and interlocks on door controller |
Bob S. |
1 |
|
|
Install new weather station and enclosure |
Steve |
2 |
|
|
Check for Building ground loop's. |
Pete? |
1 |
|
|
Lightning rods, boxes and ground cables. |
Bob S. |
1 |
|
|
Maintenance on building hatches |
Pat |
2 |
|
|
Investigate building drive fuse issue. |
Harry |
1 |
|
|
Inspect and repair hatches. |
Bob M. |
2 |
|
|
Install Evaporation Cooler for computer room HVAC system |
Tom/Steve |
1 |
|
| |
|
|
|
Telescope
|
|
|
|
|
Inspect and grease hot-vane slider. |
Steve |
1 |
|
|
Calibrate building vs. antenna limit switches.. |
Steve |
1 |
|
|
Check elevation wrap |
Steve |
1 |
|
|
Grease elevation motors and bearings. |
Steve |
1 |
|
|
Check out inclinometers. |
Pete? |
2 |
|
|
Install Thermisters on feedlegs. |
Tom/Bill |
2 |
|
|
Put inclinometer temperature probe in FMS. |
Tom |
|
|
| |
|
|
|
Pier
|
|
|
|
|
Clean and grease Az and El bearings |
Steve |
1 |
|
|
Clean & grease ring gear |
Steve |
1 |
|
|
Grease elevation motors |
Steve |
1 |
|
|
Check Az wrap for cable wear. |
Steve |
2 |
|
|
Check for gas leaks |
Steve |
1 |
|
|
Clean upper landing. |
Steve |
1 |
|
| |
|
|
|
Control System
|
|
|
|
|
Back up all observers data / user areas first |
Tom |
1 |
|
|
Upgrade all Non-Real-time Linux boxes to Fedora Core 3.0 of RH 9.0 |
Tom |
1 |
|
|
Find a permanent home for smtotux |
Tom |
2 |
|
|
Install and program zero check box on VCO's |
Tom |
1 |
|
|
Finish IF routing and software on FMS |
Tom |
1 |
|
|
Finish 'goodness of fix' function in five points. |
Tom |
2 |
|
|
We need an 'Ignore Offsets' button in Rambo Spec 5 screen |
Tom |
1 |
|
|
Rambo should indicate it's taking data. |
Tom |
2 |
|
|
Fix Tipper going below tree line? |
Tom |
2 |
|
|
Port FitIncRealtime |
Bill |
1 |
|
|
Clean out extra log messages, especially msg's to Monitor. |
Tom |
2 |
|
|
Log encoder fit parameters vs angle. |
Tom S |
2 |
|
|
Log encoder 0 pt resets and fiducial encounters w/o reset. |
Tom S |
2 |
|
|
Check out tracking at high elevation. |
Tom S |
1 |
|
|
Port NETCHECK. |
Bill |
2 |
|
|
Install cross scanning pointing. |
Tom |
2 |
|
|
Configure and Install display in lounge. |
Tom |
1 |
|
|
Implement a 9-point pointing measurement |
Tom |
2 |
|
|
Continuously measure building I's to be saved after fuse blows. |
Tom |
2 |
|
|
Reorder rcvr selection in Rambo than the alphabetic order. |
Bill |
2 |
|
|
Combine the pointing data in Dataserv. |
Tom |
2 |
|
|
Implement processing of Galactic Coord OTF's in Dataserv. |
Tom |
2 |
|
|
Fix GALACTIC label in the DataBrowse Plot. |
Tom |
2 |
|
|
Modify cts_data to allow for more than one CTS. |
Bill |
2 |
|
|
Implement different nutation frequencies in DBE. |
Tom |
1 |
|
|
Implement "Ostrich Mode" for CloudSat flyovers |
Bill/Bob |
1 |
|
|
Bad channel list for FFB |
Bill |
|
|
|
Fix grid offsets in high Dec. |
Bill |
|
|
|
Add beam offsets for all dual channel receivers. |
Bill |
|
|
|
Port Inclinometer software from Frankie to FMS |
Bill |
|
|
|
Check out tracking at high elevations. |
Bill |
|
|
|
Implement BSP grid map |
Bill |
