SMT Summer 2003

Home
Up
Emergency Info
Proposals
Facilities
Instrumentation
Systems Status
Schedules
Updates
Observer Info
Science at ARO
ARO In The News
Weather
Staff
Education
ARO FAQ
Internal Docs
Tucson Info
Jobs
Photo Gallery
Search ARO
Contacts

SMT Summer Shutdown 2003

           
Job # Done? Category Job/Description Who ? Priority
           
Buliding:          
1 NOT Mech Man lift for door seals Steve 1
2 Working Mech Roof & door seals Steve 1
3   Mech Seal door on 5th floor Steve 1
4 Working Mech Widen door between receiver rooms Steve 1
5   Mech Install hatch in receiver room Steve 1
6 Done Mech Seal vents Steve 1
7   Mech Install taumeter cover Steve 1
8 Done Mech Fireproof building Steve 2
9   Maint Reinstall drywall Steve 2
10 Done Mech Fix rubbing hydro cylinder Steve 2
11   Maint Paint fourth floor Steve 3
12 Done Mech Hydraulic service Steve 1
13 Done Maint Clean track. All 1
14   Mech Adjust building wheels Steve 1
15   Maint Crane maintenance Steve/Harry 1
16   Mech/Elec Fans in 5th floor walls Steve 2
17   Mech/Elec Building drive tests Harry et al 2
18   Electrical Heat tape checks and mods Harry 2
19   Electrical UPS to 5th floor Harry 2
20 Done Electrical Install light in chiller room Steve 3
21   Electrical Door and roof limit switches Steve/Harry 1
22   Electrical Install new weather station Steve 2
23   Electronic Building drive current signals- find noise source. Pete 1
24   Electronic Check for Building ground loop's. Pete 1
25   Program Measure (& log?) building currents. Pete/Tom 2
           
Telescope:          
26 Done Mech Inspect and grease hot-vane slider. Steve et al 1
27   Mech Calibrate building vs antenna limit switches.. Steve/Harry 1
28   Electrical Rewire Krupp for LED's. ? 1
29   Mech Check elevation wrap Steve 1
30   Program Check out inclinometers. Bill/Pete 2
31   Electronic Inclinometer low pass filter -PCB and hook up temp sensor. Pete 1
           
Peir:          
32 Done Mech Clean and grease Az and El bearings Steve et al 1
33   Mech Clean & grease ring gear Steve 1
34   Mech Grease elevation motors Steve 1
35   Mech Check Az wrap for cable wear. Steve 2
           
Control System:          
36 Done Admin Back up all observers data / user areas Tom 1
37 Working Admin Upgrade all Non-Realtime Linux boxes to RH7.3 Tom 1
38 Working Admin Get all Linux boxes on RHN Tom 1
39 Done Admin Install firewall Tom 1
40 Done Admin Identify any bad scsi disks on tux and replace or repair. Tom 1
41 Done Admin Find a permanent home for smtotux Tom 2
42 Working Program Clean up CACTUS_GLOBAL. Tom 1
43   Program Install receiver fuctions in global memory. Tom 1
44   Program Install and program zero check box on VCO's Pete/Tom 1
45 Started Program Finish IF routing and software on FMS Pete/Tom 1
46 Working Program Order and install new FMS mother board Tom 1
47   Program Finish 'goodness of fix' function in five points. Tom 2
48   Program We need an 'Ignore Offsets' button in Rambo Spec 5 screen Tom 1
49   Program Allow accepting individual channels in fits. Tom 2
50   Program Rambo should indicate it's taking data. Tom 2
51   Program Line name into headers Tom 1
52   Program Spec 5 offsets are not in class files. Tom 1
53   Program Inproper beams alarm. Tom 1
54   Program Fix Tipper going below tree line? Tom 2
55   Program Put final touches on remote observing package. Tom 2
56   Admin Finish remote observing document Tom 2
57 Done Program Port UPSsuck, WeatherSuck, and WindSuck. Bill 1
58   Program Port Tipsuck. Bill 1
59   Program Port FitIncRealtime Bill 1
60 Done Admin Download the terminal servers from Linux. Bill 1
61   Program Log sun distance and angle. Tom 2
62 Done? Program SAMBUS channels 27-31 (+ ...) don't work. Bill/Pete 2
63 Done Program What about spontaneous 0x80 bit? Bill/Pete 2
64 ---- Program Get latching mode to work in VxWorks 0-15 Bill/Pete 2
65 Done Admin Turn on Linux xdm server for X-terminals. Bill 2
66   Program Remember focus & pointing settings between receiver changes. Tom 1
67   Program Clean out unneeded log messages, especially msg's to Monitor. Tom/Bill 2
68   Program Log encoder fit parameters vs angle. Tom S/Tom 2
69   Program Log encoder zero point resets and fiducial encounters w/o reset. Tom S./Tom 2
70   Program Make successive tracker polynomials join at the ends. Tom S. /Bill 1
71   Program Check out tracking at high elevation and high speed (holo) Tom S. /Bill 1
72   Program Make servo work with both elevation encoders. Tom S. 1
73   Program More Testing of Sun Avoidance. Tom S. 1
74   Program Servo recoverery during drive cycling. Tom S. 1
75   Program Port NETCHECK. Bill 2
76   Program Install raster scanning pointing. Tom/Bill 2
77 Working Program Configure and Install displays in kitchen and lounge. Tom 1
78   Admin Upgrade Autocad on mountain. Carlson 2
79   Program Add VATT weather info to our displays. Tom 3
80 Done Program Clean up 'mailboxdefs' file Tom 1
81   Program BSCAL should not be done on source. Tom 1
82   Program Add Vane temperature to GLOBAL Tom 1
83 Done Program Rewrite mailboxdefs file Tom 2
           
           
Prime Focus:          
84   Computing Install sensors on focus translation stage and quadrapod. Bob S./Tom 1
85   Computing Thermal test on Sub-Reflector? ? 2
86   Computing Check sun limits and for heating of focus translation stage. Tom/Bill/Tom 1
87   Computing Move the lower limit switch on Focus Motor #1 0.3 mm or so. ? 2
88   Mech Subreflector Work ( remove from telescope) Steve/Harry 1
89   Maint Touch up paint work on quadrapod ? 2
90   Mech Optical telescope tests Tom 3
91   Computing Pinhole camera tests Bill et al 1
92 Working Computing Get Optical focus to work w/o laptop. Tom 1
93 Working Computing Get Optical pointing mode up w/o twf. Tom 1
94   Computing Get Optical focus stage with more range? ? 2
           
Receivers:          
95   Receiver Cold Head maintenance Martin 1
96   Receiver Compressor repairs and modifications Martin 2
97   Receiver Install 2mm JT receiver Harry 1
98   Receiver Tuning tests, 345 GHz Harry 2
99   Electronic Bias Box modifications 460 GHz Harry 2
100 Done Receiver Change oil in vacuum pump Steve 2
101   Electrical Install power for compressor Steve 2
102   Mech Repair light tower limit switch. Pat 1
           
Backends/IF:          
103   Electronic Filter Bank tests and repairs Harry 2
104   Electronic Chirp Downconverter mods (2.1 GHz IF ) Harry 1
105   Electronic New cables for the Backend Switch Box Martin 2
106 Working Electronic IF back end box; Finish instillation. Pete 1
107 Working Electronic VCO Zero box- PCB and construction. Pete 1
108 Working Electronic Encoder power supplies- Change to external 115 Volts.. Pete 1
109 Working Electronic New Encoder amplifier boards- PCB layout and construction. Pete 1
           
Misc:          
110   Electronic 10 MHz Distribution noise tests Harry 2
111   Electronic Temperature monitor for Maser Room Harry 3
112   Mech Siding on Hilton Steve 2
113   Mech Clean Basecamp container Steve 3
114   Mech Purchase and install weather station box. Robert 2
115 Done Purchase Purchase and install new audio system. Bill Hale et al 3
           

 Copyright Arizona Radio Observatory.
For problems or questions regarding this web contact [tfolkers{at}as{dot}arizona{dot}edu].
Last updated: 09/04/08.